?功能介紹

• ?以51/STM32單片機作為主控系統；
• ? LCD1602液晶顯示當前時間、溫濕度、藥品重量
• ? 3次吃藥時間、藥品類目和藥品數量
• ?HX711壓力采集當前藥品重量
• ?紅外感應當前藥盒是否打開
• ?DS1302時鐘芯片顯示當前年月日、時分秒、星期
• ?DHT11采集當前環境溫度和濕度? ? ? ? ? ? ? ? ? ? ? ? ? ? ?
• 手機端連接WIFI后可以顯示當前溫濕度、重量、吃藥時間等信息
• 手機端可以設置當前吃藥時間、藥品種類、藥品數量等信息
• 當吃藥時間到后手機端震動提醒
• 并且進行語音播報：“吃藥時間到了，請及時吃藥”
• 手機端點擊“已吃藥”停止震動和播報
• ?整個電路以5v供電;

?電路圖

PCB

源代碼

#include <reg52.h>
#include <intrins.h>
#include <stdio.h>//printf串口輸出頭文件

#define uchar unsigned char
#define ushort  unsigned int
#define uint  unsigned long

#include "lcd1602.h"
#include "uart_trx.h"
#include "eeprom52.h"

#define RATIO 800		//系數，建議選擇800-1000

sbit key1 = P1^0;//加鍵
sbit key2 = P1^1;//減鍵

sbit beep = P2^0;//蜂鳴器
sbit Fan = P1^3;//風扇

unsigned char pmBuf[7] = 0;//數據接收數組
uint PM25_Value = 0;     		//PM = ((pmBuf[1]<<8)+pmBuf[2])/1024*8*ratio
uint PM25_ValueMax = 200; //上限初始值

void EEPROM_WRITE()//EEPROM寫入
{
		SectorErase(0x2000);//擦除扇區
	  byte_write(0x2001, (PM25_ValueMax>>8)&0xFF);//存儲高8位
	  byte_write(0x2002, (PM25_ValueMax>>0)&0xFF);//存儲低8位
	  byte_write(0x2009, 111);//存儲校驗值
}

void EEPROM_READ()//EEPROM讀出
{
		if(byte_read(0x2009)!=111)//開機檢測單片機是不是第一次使用，如果不是第一次使用，則先把數據存儲一遍，再讀取，數據就不會亂碼
		{
				EEPROM_WRITE();//存儲
			  delay_ms(100);
		}
		PM25_ValueMax = byte_read(0x2001)<<8 | byte_read(0x2002);//讀取上限值
}

void Get_PM(void)//讀取PM2.5值，具體的數據幀意思，請自行查閱芯片手冊
{
    char i = 0;
    char j = 0;
    char k = 0;

	  COM.RX_Cnt = 0;
    if(COM.B_RX_OK == 1)//串口數據接收完成
    {
        for(i = 0; i<8; i++)
        {
            if((RX_Buffer[i] == 0xAA)&&(RX_Buffer[i+6]==0xFF))//判斷接收的數據是否正確
            {
                goto find2;
            }
        }
        goto end2;
find2:
        for(j = 0; j<7; j++)
        {
            pmBuf[j] = RX_Buffer[i+j];//數據獲取
        }

        PM25_Value = (unsigned int)((pmBuf[1]*256)+pmBuf[2])*5/2048.0*RATIO;//計算PM2.5值
        COM.B_RX_OK = 0;
    }
end2:
    return;
}



void main(void)
{
    unsigned int test;

	  EEPROM_READ();//開機讀取存儲值
    LCD_init();//1602初始化
    Uart_Init(2400);//串口初始化波特率2400
  
    LCD_write_string(0,0,"Pm2.5:    ug/m3 ");
    LCD_write_string(0,1,"PmMax:    ug/m3 ");
	  //顯示上限值
	  LCD_write_char(7, 1, PM25_ValueMax % 1000 / 100 + 0x30);
		LCD_write_char(8, 1, PM25_ValueMax % 100 / 10 + 0x30);
		LCD_write_char(9, 1, PM25_ValueMax % 10 + 0x30);
    while(1)
    {
			if (test ++ > 250)//大約250ms讀取一次
			{
					test = 0 ;

					Get_PM();//獲取PM2.5
					if(PM25_Value > 999)//限值，最大999
					 PM25_Value = 999;
					//顯示PM2.5
					LCD_write_char(7, 0, PM25_Value % 1000 / 100 + 0x30);
					LCD_write_char(8, 0, PM25_Value % 100 / 10 + 0x30);
					LCD_write_char(9, 0, PM25_Value % 10 + 0x30);
					
					if(PM25_Value >= PM25_ValueMax)//超過上限，蜂鳴器報警
					{
							beep = ~beep;
						  Fan = 0;
						  delay_ms(100);
					}
					else
					{
							beep = 1;
						  Fan = 1;
					}
			}
			if(key1 == 0)//加鍵按下
			{
					delay_ms(10);//消抖
				  if(key1 == 0)
					{
						  beep = 0;
						  delay_ms(100);
						  beep = 1;
							while(key1 == 0);
						  if(PM25_ValueMax<999)PM25_ValueMax+=10;//上限最大到999，每次加10
						  //顯示
						  LCD_write_char(7, 1, PM25_ValueMax % 1000 / 100 + 0x30);
							LCD_write_char(8, 1, PM25_ValueMax % 100 / 10 + 0x30);
							LCD_write_char(9, 1, PM25_ValueMax % 10 + 0x30);
						  EEPROM_WRITE();//保存
					}
			}
			if(key2 == 0)//減鍵按下
			{
					delay_ms(10);
				  if(key2 == 0)
					{
						  beep = 0;
						  delay_ms(100);
						  beep = 1;
							while(key2 == 0);
						  if(PM25_ValueMax>=10)PM25_ValueMax-=10;//上限最小到0，每減10
						  //顯示
						  LCD_write_char(7, 1, PM25_ValueMax % 1000 / 100 + 0x30);
							LCD_write_char(8, 1, PM25_ValueMax % 100 / 10 + 0x30);
							LCD_write_char(9, 1, PM25_ValueMax % 10 + 0x30);
						  EEPROM_WRITE();//保存
					}
			}
			delay_ms(1);
    }
}

? ? ?

元器件清單

參考文獻

參考文獻
[1]王德保.GPS在城市控制網中的應用研究[D].山東:山東科技大學,2005.
[2]何立民.從現代計算機視角看嵌入式系統(4)嵌入式系統40年發展史[J].單片機與嵌入式系統應用,2016,16(04):77-79.
[3]康桂霞,劉達.FPGA應用技術教程[M].北京:人民郵電出版社:201306.229.
[4]樸德慧,衣英剛.液晶顯示器驅動板MCU電路介紹(上)[J].家電檢修技術,2012(11):53.
[5]段廷魁.全球衛星定位系統（GNSS）在工程測量中的實踐運用探索0[J].科技創新與應用,2021(05):182-184.
[6]宋戈,黃鶴松.51單片機應用開發范例大全[M].北京:人民郵電出版社:國家信息技術緊缺人才培養工程系列叢書,201206.558.
[7]羅小青.單片機原理及應用教程[M].北京:人民郵電出版社,201409.180.
[8]沈慶陽.單片機實踐與應用[M].北京:清華大學出版社,2002.
[9]杜深慧.溫濕度檢測裝置的設計與實現[M].北京:機械工業出版社,2004.
[10]林嘉.基于89S52的LCD1602程序設計[J].電腦知識與技術,2012(26):6376-6378.
[11]劉光偉.基于單片機的溫室溫濕度監測系統設計與實現[D].秦皇島市:燕山大學,2012.
[12]褚福強,董學仁.單片機的網絡接入技術研究[J].儀器儀表用戶,2006(05):4-5.
[13]陳英俊.基于單片機的溫濕度監測和報警系統設計[J].廣東石油化工學院學報,2013(04):42-46.
[14]廖麗媛.基于應變式扭矩傳感器的測量系統的設計[D].上海市:東華大學,2013.
[15]劉九慶.溫室環境工程技術[M].吉林:東北林業大學出版社,2002.
[16]王明喜,崔世茂.大棚型日光溫室光照、溫度及濕度等性能的初步研究[J].農業工程技術(溫室園藝),2008(05):19-21.
[17]張迎輝.單片微型計算機鍵盤接口設計[J].信息技術,2004(07):68-69+91.
[18]張友德,趙志英.單片微型機原理應用與實驗[M].上海市:復旦大學出版社,2003.
[19]趙芝蕓.溫室智能監控系統[D].江蘇:江蘇科技大學,2010.
[20]張宏偉.基于STM32的智能環境監測系統設計與實現[J].大慶師范學院學報,2020(05):32-35.
[21]王世偉,楊越.基于STM32的多型號舵機調試器設計[J].九江學院學報(自然科學版),2020,35(02):33-36.
[22]Pengcheng Zhao,Meijun Ni,Chao Chen,Chenxi Wang,PingpingYang,Xiahui Wang,Chunyan Li,Yixi Xie,Junjie Fei. A Novel Self-protection Hydroquinone Electrochemical Sensor Based on Thermo -sensitive Triblock Polymer PS-PNIPAm-PS[J].
[23]Jian Wang,Jing Chen,Xiaofu Xiong,Xiaofeng Lu,ZhengLiao,Xiaobo Chen.Temperature safety analysis and backup protectionscheme improvement for overhead transmission line in poweroscillation condition[T].Electric Power Systems Research,2019,166.
[24]Fuji Electric Co.Ltd.;Patent Issued for SeiconductorDevice And Method Of Outputting Temperature Alarm (USPTO10,164,626)[J].Electronics Newsweekly,2019.
[25]VERSID,INC;Patent Issued for Refrigeration UnitTemperature Alarm Using Thermal Properties of Food to Eliminate FalseAlarms (USPTO 9752810)[J].Computers,Networks &Communications,2017.
[26]Fuji Electric Co.Ltd;Patent Application Titled"Semiconductor Device and Method of Outputting Teperature Alarm"Published Online (USPTO 20170077919)[J]. Technology & BusinessJournal,2017.
[27]su Yuanping,Xu Lihong,Goodman Erik D.Multi-layerhierarchical optimisation of greenhouse climate setpoints for energyconservation and improvement of crop yield[J].Biosystems
[28]黃松茂.基于STM32的家庭環境監測系統的設計與實現[D].甘肅蘭州.西北師范大學,2018.:23-30.
[29]李大琳.智能車內溫度監測系統設計[J].山東工業技術,2014(12):80-81.
[30]郭雯,王海濤. 智能輸液系統的發展與應用.醫療衛生裝備,2012

?實物可做，資料齊全，其他功能也可做~?文章來源地址http://www.zghlxwxcb.cn/news/detail-827038.html

到了這里，關于基于51/STM32單片機的智能藥盒 物聯網定時吃藥 藥品分類的文章就介紹完了。如果您還想了解更多內容，請?jiān)谟疑辖撬阉鱐OY模板網以前的文章或繼續瀏覽下面的相關文章，希望大家以后多多支持TOY模板網！